Dryer repair
If it takes two cycles to dry a load, something's wrong, and it's costing you on every run. We fix gas and electric dryers and clear the vent while we're there.
What we service
Open every day
7:00 AM – 11:00 PM
95% one-trip fixes
Common parts on board
90-day warranty
Parts and labor covered
Price before work
Approved by you first
Symptoms we see
Nearly every dryer complaint traces back to heat, airflow, or motion. Which one it is decides how long the repair takes.
Electric dryers lose the heating element or a thermal fuse. Gas models usually have a failed igniter or flame sensor. Both are common and both are fixable.
Almost always restricted airflow. A blocked vent line makes the dryer work twice as long, and it's the leading cause of dryer fires in the area.
A snapped belt is the usual answer, though worn drum rollers or a seized idler pulley produce the same symptom with more noise first.
Rollers and the idler pulley wear down over years of use. Caught early it's a cheap fix, left alone it takes the belt and motor with it.
An overheating dryer trips its own safety. That's the thermal fuse doing its job, and it points straight back to airflow or a stuck thermostat.
A failed door switch, start switch, or thermal fuse breaks the circuit. We test each one rather than replacing all three.
How we work
We check heat output and airflow together, because one hides the other. A dryer with a weak element and a blocked vent looks identical to one with just a bad element until you measure both.
Every visit includes a look at the vent run. If the line is packed with lint, we tell you, because a restricted vent is both a fire risk and the reason a new heating element fails early.

Error codes
Dryer codes point mostly at heat, airflow, and moisture sensing. Here's what the common ones mean on the models we see around Fort Worth.
| Code | Brand | What it usually points to |
|---|---|---|
| D80 / D90 / D95 | Samsung | Vent restriction detected. The dryer is telling you airflow is blocked somewhere in the duct run. |
| HE / tE | Samsung / LG | Heating element or thermistor fault. Either no heat at all or wildly inaccurate temperature readings. |
| D80 / dE | LG | Duct blockage or door not sensed as closed, depending on model generation. |
| F22 / F23 | Whirlpool / Maytag | Thermistor open or shorted. The board can't trust the temperature reading and cuts the heat. |
| F01 / F30 | Whirlpool | Main control board fault or restricted airflow flagged by the moisture sensor. |
| E60 / E64 | GE Profile | Heater relay or element circuit failure. Drum turns, nothing warms up. |
| PF | Whirlpool / Maytag | Power failure mid-cycle. Harmless once, worth investigating if it repeats. |
| E1 / E2 | Frigidaire / Electrolux | Temperature sensor or control fault, often paired with a dryer that shuts off early. |
Vent restriction detected. The dryer is telling you airflow is blocked somewhere in the duct run.
Heating element or thermistor fault. Either no heat at all or wildly inaccurate temperature readings.
Duct blockage or door not sensed as closed, depending on model generation.
Thermistor open or shorted. The board can't trust the temperature reading and cuts the heat.
Main control board fault or restricted airflow flagged by the moisture sensor.
Heater relay or element circuit failure. Drum turns, nothing warms up.
Power failure mid-cycle. Harmless once, worth investigating if it repeats.
Temperature sensor or control fault, often paired with a dryer that shuts off early.
Vent codes are worth taking seriously. A blocked duct makes the dryer run hot and long, which is both the leading cause of dryer fires and the reason replacement elements fail early.
Brands
From basic vented dryers to heat-pump and Speed Queen units, we carry elements, igniters, belts, and fuses for the models we see most.
Service area
Dryer calls across Fort Worth, including the older homes where the vent run is long and awkward. We handle those too.
We're based here
2515 NE 36th St #18, Fort Worth, TX 76111, USA
Open every day, 7:00 AM – 11:00 PM.
ZIP codes we cover
Reviews
Took three cycles to dry a load of towels. He found the vent packed solid and the element half gone. Fixed both, and now one cycle does it.
Dryer was squealing loud enough to hear upstairs. Worn rollers. He replaced them and the belt, and the thing is silent now.
No heat at all on our gas dryer. He tested the igniter, swapped it, and had it running in under an hour. Told me the price before starting.
Book a repair
Send your details and we'll ring you back to set a same-day or next-morning slot. In a hurry? Just call.
How it works
Working hours
Every day: 7:00 AM – 11:00 PM
Call us directly
(817) 330-5698Share a few details and we'll follow up shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Your request has been sent. We'll call you back shortly to confirm your visit.